GLOSSARY ENTRY (DERIVED FROM QUESTION BELOW) | ||||||
---|---|---|---|---|---|---|
|
12:40 Dec 30, 2010 |
English to Dutch translations [PRO] Tech/Engineering - Mechanics / Mech Engineering / oil pump | |||||||
---|---|---|---|---|---|---|---|
|
| ||||||
| Selected response from: Jack den Haan Netherlands Local time: 19:09 | ||||||
Grading comment
|
Summary of answers provided | ||||
---|---|---|---|---|
3 | vastlager, niet-stellend lager |
|
Summary of reference entries provided | |||
---|---|---|---|
Reference for non-locating bearing |
|
Discussion entries: 6 | |
---|---|
vastlager, niet-stellend lager Explanation: Ik weet het niet helemaal zeker, maar bij nader inzien denk ik dat je 'non-locating' hier kunt vertalen met 'vastlager' of eventueel niet-stellend lager'. Dit in tegenstelling tot loslagers, die vermoedelijk ook stellende lagers of stellagers genoemd worden. Nogmaals, ik ben hier niet zeker van. Zie de onderstaande referenties. http://en.wikipedia.org/wiki/Ball_bearing Avoiding undesirable axial load The part of a bearing that rotates (either axle hole or outer circumference) must be fixed, while for a part that does not rotate this is not necessary (so it can be allowed to slide). If a bearing is loaded axially, both sides must be fixed.[3] If an axle has two bearings, and temperature varies, axle shrinks or expands, therefore it is not admissible for both bearings to be fixed on both their sides, since expansion of axle would exert axial forces that would destroy these bearings. Therefore, at least one of bearings must be able to slide.[3] A 'freely sliding fit' is one where there is at least a 4 um clearance, presumably because surface-roughness of a surface made on a lathe is normally between 1.6 and 3.2 μm.[3] http://www.brammer.nl/nl/nl_brammer_self_aligning_bearings.a... Zich instellende lagers Het tweerijige zich instellende kogellager heeft twee rijen kogels en een gemeenschappelijke bolvormige loopbaan in de buitenring. Hierdoor kan het lager zichzelf instellen en is het ongevoelig voor scheefstellingen van de as ten opzichte van het lagerhuis. Dit lager is bijzonder geschikt voor lagerconstructies waarbij rekening moet worden gehouden met aanzienlijke asdoorbuigingen of uitlijnfouten. Een ander voordeel van zich instellende kogellagers is dat zij de laagste wrijving van alle wentellagers hebben, zodat dit lager ook bij hoge toerentallen minder wrijvingswarmte genereert. http://www.aknbearing.com/pages/snx.pdf SNX huizen zijn gedeelde staande lagerhuizen die de vroegere series SN, S en SNA opvolgen. Door optimalisering van de constructie zijn zij hoger belastbaar dan de voorgangers bij gelijkblijvende hoofdafmetingen (ISO 113/II/1979). SNX huizen zijn geschikt voor tweerijige zich instellende kogellagers en tonlagers, zowel met conische als met cilindrische boring. De huisboring (H7) laat toe dat het lager in het huis heen en weer kan schuiven zodat een loslager gegeven is. In de regel wordt één huis op een as uitgevoerd als [b]vastlager hetgeen bereikt wordt door naast het lager stelringen FRB te monteren (…) Gedeelde cilinderlagers Gedeelde cilinderlagers SCRB werden speciaal voor toepassing in de gedeelde huizen SNX ontwikkeld. Doordat het lager net als het huis axiaal gedeeld is wordt montage en demontage een stuk eenvoudiger. Het lager behoeft niet over de as te worden geschoven. Bij vervanging is het niet nodig onderdelen die naast het huis op de as gemonteerd zijn te demonteren. Als dichting worden de eveneens gedeelde tweelippendichting (zie par. 1.2.2) of de gedeelde viltringafdichting (zie paragraaf 1.2.3) geadviseerd. Er is een vastlageruitvoering (SCRB... F) en een loslager uitvoering (SCRB... L) beschikbaar. Stelringen FRB worden derhalve niet toegepast. Onderstaande tabel geeft een overzicht van de beschikbare lagertypes. De afmetingen en verdere gegevens omtrent de in de tabel genoemde huizen zijn opgenomen in de maattabellen op blz. 58 http://www.brammer.be/images/sce/Downloads/Netherlands/Hulpa... Huis aan één zijde gesloten voor een niet doorgaande as, uitgevoerd als vastlager. AH Bij naaldlagers: gewijzigde inwendige constructie. Inzet-geharde kooi. AL Huis aan één zijde gesloten voor een niet doorgaande as, uitgevoerd als loslager |
| |
Login to enter a peer comment (or grade) |
22 hrs |
Reference: Reference for non-locating bearing Reference information: http://evolution.skf.com/zino.aspx?articleID=470 Preadjustable non-locating bearing unit The SKF Panloc is a non-locating bearing unit that allows the internal clearance or preload to be adjusted to specific values. TECHNOLOGY In the area of high-precision non-locating bearings, there are numerous applications where the non-locating bearing of the shaft must have a specific internal clearance/preload in operation. In such applications, great value is placed on a precisely defined shaft position. In addition, there is an optimal operating condition for each bearing that represents a compromise between service life, rigidity and heat generation in the bearing. [JdH: As I understand it, this seems to indicate that the difference between locating and non-locating bearings is related to positioning rather than -- in first instance -- axial or radial support.] |
| |
Login to enter a peer comment (or grade) |
Login or register (free and only takes a few minutes) to participate in this question.
You will also have access to many other tools and opportunities designed for those who have language-related jobs (or are passionate about them). Participation is free and the site has a strict confidentiality policy.