zac.

English translation: tightening torque

GLOSSARY ENTRY (DERIVED FROM QUESTION BELOW)
Polish term or phrase:zac.
English translation:tightening torque
Entered by: Frank Szmulowicz, Ph. D.

15:14 Apr 8, 2018
Polish to English translations [PRO]
Tech/Engineering - Aerospace / Aviation / Space / airplanes
Polish term or phrase: zac.
[samolot MiG-29]


Uwaga: 1. Dopuszcza się założenie podkładki dodatkowej lub wymianę na nową σ = 2 mm.
2. Śruby dociągać ręcznie do oporu kluczami dynamometrycznymi:
c. dla śrub Ø 8 mm M zac. = 160 ±10 kG—cm;
d. dla śrub Ø 10 mm M zac. = 350 ±10 kG—cm;
e. dla śrub Ø 12 mm M zac. = 640 ±10 kG—cm.
Diana Kokoszka
United States
Local time: 18:48
tightening torque
Explanation:
klucz dynamometryczny = torque wrench

Tightening torque results in clamping force.

ccccc
A very common method for checking the tightening torque is to use a click wrench, which is a torque wrench equipped with a clutch that can be pre-adjusted to a specific torque. If the torque is greater than the preset torque value the clutch will release with a click.
https://www.atlascopco.com/content/dam/atlas-copco/industria...



--------------------------------------------------
Note added at 38 mins (2018-04-08 15:52:39 GMT)
--------------------------------------------------

cccccccccc
(here in foot-pounds, not kilogram force-centimeters)
Tightening Torque Guide for Grade 5 & 8 Hex Cap Screws
These Figures represent an estimate of torque (torque being the measurement of friction, not tension) required to induce given preload (clamp load) in a bolt for non-critical applications only. For critical or special applications where greater control is desired this should be experimentally determined. This applies to washer faced or double chamfered hex nuts (or bolts, if bolt is torqued) having a width across flats of approximately 1.5 times the nominal diameter and having threads free of interference.
http://www.almabolt.com/pages/catalog/bolts/tighteningtorque...

--------------------------------------------------
Note added at 51 mins (2018-04-08 16:06:01 GMT)
--------------------------------------------------

ccccccccccccccccccc
Zac. jest skrótem od zacisku, czyli clamping, ale clamping load jest siłą, a kG-cm jest momentem obrotowym, czyli tightening torque.
ccccccccccccccccccccccccccccccccccccccccccc
Selected response from:

Frank Szmulowicz, Ph. D.
United States
Local time: 18:48
Grading comment
4 KudoZ points were awarded for this answer



Summary of answers provided
3tightening torque
Frank Szmulowicz, Ph. D.


Discussion entries: 1





  

Answers


35 mins   confidence: Answerer confidence 3/5Answerer confidence 3/5
tightening torque


Explanation:
klucz dynamometryczny = torque wrench

Tightening torque results in clamping force.

ccccc
A very common method for checking the tightening torque is to use a click wrench, which is a torque wrench equipped with a clutch that can be pre-adjusted to a specific torque. If the torque is greater than the preset torque value the clutch will release with a click.
https://www.atlascopco.com/content/dam/atlas-copco/industria...



--------------------------------------------------
Note added at 38 mins (2018-04-08 15:52:39 GMT)
--------------------------------------------------

cccccccccc
(here in foot-pounds, not kilogram force-centimeters)
Tightening Torque Guide for Grade 5 & 8 Hex Cap Screws
These Figures represent an estimate of torque (torque being the measurement of friction, not tension) required to induce given preload (clamp load) in a bolt for non-critical applications only. For critical or special applications where greater control is desired this should be experimentally determined. This applies to washer faced or double chamfered hex nuts (or bolts, if bolt is torqued) having a width across flats of approximately 1.5 times the nominal diameter and having threads free of interference.
http://www.almabolt.com/pages/catalog/bolts/tighteningtorque...

--------------------------------------------------
Note added at 51 mins (2018-04-08 16:06:01 GMT)
--------------------------------------------------

ccccccccccccccccccc
Zac. jest skrótem od zacisku, czyli clamping, ale clamping load jest siłą, a kG-cm jest momentem obrotowym, czyli tightening torque.
ccccccccccccccccccccccccccccccccccccccccccc

Frank Szmulowicz, Ph. D.
United States
Local time: 18:48
Specializes in field
Native speaker of: Native in EnglishEnglish, Native in PolishPolish
PRO pts in category: 120
Login to enter a peer comment (or grade)



Login or register (free and only takes a few minutes) to participate in this question.

You will also have access to many other tools and opportunities designed for those who have language-related jobs (or are passionate about them). Participation is free and the site has a strict confidentiality policy.

KudoZ™ translation help

The KudoZ network provides a framework for translators and others to assist each other with translations or explanations of terms and short phrases.


See also:

Your current localization setting

English

Select a language

Term search
  • All of ProZ.com
  • Term search
  • Jobs
  • Forums
  • Multiple search